Motor Driver
Showing 1–25 of 30 results
-
Motor Drivers / PWM Controller, Robotics, Show All Robotics
6VDC-90VDC PWM DC Motor Speed Controller 10A High Power Stepless Speed Regulation Controller
Motor Drivers / PWM Controller, Robotics, Show All Robotics6VDC-90VDC PWM DC Motor Speed Controller 10A High Power Stepless Speed Regulation Controller
6V To 90V PWM Speed Controller For 12V DC Brushed Motor With 10A High Power Step-less Speed Regulator
Speed controller introduction
1. Voltage range: DC 6V – 90V
6V 60W ; 12V 120W ; 24V 240W ; 48V 480W ; 72V 700W ; 90V 900W ;
2. Rated current 10A; maximum current 15A; It is recommended that this governor use a brushed DC motor within 10A.
3. PWM output range 0%-100%; motor can be adjusted to stop, or can be adjusted to the highest speed
4. Frequency : 13kz
SKU: MOD3009 -
CNC / 3D Printers, Drivers & Controllers, Motor Drivers / PWM Controller, Other CNC Accessories, Robotics, Show All CNC
A4988 DRV8825 Stepper Motor Driver Control Extension Shield For CNC 3D Printer
CNC / 3D Printers, Drivers & Controllers, Motor Drivers / PWM Controller, Other CNC Accessories, Robotics, Show All CNCA4988 DRV8825 Stepper Motor Driver Control Extension Shield For CNC 3D Printer
1. For A4988 / DRV8825
2. Jumpers are hit on the DP position representing 16 segments (4988) or 32 segments (8825).
3. Jm connected to the motor.
4. Jv connect 5V and 12V-24V power supply
5. Jc E / S / D / G corresponding to the connection on the Enable Step Dir Gnd drive signal output.
6. Size: 34x41mm
SKU: CNC4706 -
Motor Drivers / PWM Controller, Robotics
DC 12V 24V 3A PWM DC Motor Speed Controller Reversible Relay Module 6V-28V
Motor Drivers / PWM Controller, RoboticsDC 12V 24V 3A PWM DC Motor Speed Controller Reversible Relay Module 6V-28V
Description:
1203BS DC Motor Speed Regulator controls the speed of a DC motor by adjusting Pulse-Width-Modulated (PWM)
The input power range is DC 6-28V
Control the forward or reverse direction and the stop of DC motor by button switch.
Press the green button, the motor reverses rotates; and release the button, the motor stops
Press the red button, the motor clockwise rotates; and release the button, the motor stops
SKU: MOD3022 -
Modules, Motor Drivers / PWM Controller, Robotics, Show All Modules, Show All Robotics
DC 12V-40V 10A Speed Controller PWM Stepless Speed Change
Modules, Motor Drivers / PWM Controller, Robotics, Show All Modules, Show All RoboticsDC 12V-40V 10A Speed Controller PWM Stepless Speed Change
The input supply voltage range is 12V-40VDC.
Power: 0.01-400w
frequency is 13khz
PWM pulse width speed range: 10% – 100%
Incorporate a 10A fuse, and with reverse connection power supply protection function.
SKU: MOD3010 -
Modules, Motor Drivers / PWM Controller, Robotics, Show All Robotics
DC 6V 12V 24V 28VDC 3A 80W PWM Motor Speed Controller Regulator 1203BK
Modules, Motor Drivers / PWM Controller, Robotics, Show All RoboticsDC 6V 12V 24V 28VDC 3A 80W PWM Motor Speed Controller Regulator 1203BK
Description:
This DC Motor Speed Controller allows controlling the direction of a DC motor using a Pulse– Width-Modulated (PWM) DC voltage with a Duty Cycle fully adjustable from 0%-100%.
The motor speed controller can easily provide a continuous current of3A to your DC motor or other DC load.
SKU: MOD3013 -
CNC / 3D Printers, Drivers & Controllers, Motor Drivers / PWM Controller, Robotics, Show All CNC
DM542 Stepper Motor Controller 2-phase Digital Stepper Motor Driver 18-48 VDC Max. 4.2A for 57 86 Series Motor
CNC / 3D Printers, Drivers & Controllers, Motor Drivers / PWM Controller, Robotics, Show All CNCDM542 Stepper Motor Controller 2-phase Digital Stepper Motor Driver 18-48 VDC Max. 4.2A for 57 86 Series Motor
DM542 is a new type of two-phase hybrid stepping motor driver, The drive voltage of which is from 20VDC to 50VDC. It is designed for use with a 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor to run smoothly almost without noise and vibration.
SKU: MOD3020 -
CNC / 3D Printers, Drivers & Controllers, Motor Drivers / PWM Controller, Robotics, Show All CNC
DRV8825 Stepper Motor Driver With Heatsink
CNC / 3D Printers, Drivers & Controllers, Motor Drivers / PWM Controller, Robotics, Show All CNCDRV8825 Stepper Motor Driver With Heatsink
The DRV8825 stepper motor driver carrier board TI DRV8825 micro bipolar stepper motor drive is a breakthrough. The module has a pinout and interface with our A4988 stepper motor driver carrier is almost the same, so it can be used as a better performance of the pull-down menu board replacement in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 – 45 V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling).
SKU: CNC4530 -
Communication, Mother Boards, Motor Drivers / PWM Controller, Robotics, Show All Robotics, Wi-Fi Series Boards, Wi-Fi Transceivers
ESP8266 Wi-Fi Motor Drive Expansion Board L293D ESP12E Lua Internet Of Things Smart Car DIY *Without NodeMCU
Communication, Mother Boards, Motor Drivers / PWM Controller, Robotics, Show All Robotics, Wi-Fi Series Boards, Wi-Fi TransceiversESP8266 Wi-Fi Motor Drive Expansion Board L293D ESP12E Lua Internet Of Things Smart Car DIY *Without NodeMCU
ESP-12E motor drive expansion board
Introduction:
Development of the first motor driven expansion board based on ESP-12E.
Characteristic:
L ESP12 DEV KIT development board expansion module;
L leads to all function pins of ESP12 DEV KIT: SPI, UART, GPIO, AI and 3.3V power interface.
L extends two motor drives, which can directly drive two motors.
SKU: MOD3017 -
Motor Drivers / PWM Controller, Robotics, Show All Robotics
L293D Motor Driver Mini Expansion Board L293D Motor Driver Module Board
Motor Drivers / PWM Controller, Robotics, Show All RoboticsL293D Motor Driver Mini Expansion Board L293D Motor Driver Module Board
New L293D motor shield, the input voltage DC4.5-25V
600mA OUTPUT CURRENT CAPABILITY PER CHANNEL
1.2A PEAK OUTPUT CURRENT (non repetitive)PER CHANNEL
ENABLE FACILITY
OVERTEMPERATURE PROTECTION
LOGICAL “0” INPUT VOLTAGE UP TO 1.5 V(HIGH NOISE IMMUNITY)
INTERNAL CLAMP DIODES
SKU: MOD3018 -
Modules, Motor Drivers / PWM Controller, Robotics, Show All Modules, Show All Robotics
L298P PWM Speed Controller Shield Dual High-Power H-bridge Driver ,Bluetooth Interface for Arduino
Modules, Motor Drivers / PWM Controller, Robotics, Show All Modules, Show All RoboticsL298P PWM Speed Controller Shield Dual High-Power H-bridge Driver ,Bluetooth Interface for Arduino
Technical Specifications:
1.Logical part of the input voltage VD: 5V
2.Drivenpart of the input voltage VS: VINInput6.5 ~ 12V, PWRIN4.8 ~ 35Vinput
3.Logicalpart of the working current : <36mA
4.Drivenpart of the operating current : <2A
5.Maximum power dissipation: 25W (T = 75Celsius)
SKU: MOD3015 -
Motor Drivers / PWM Controller, Robotics, Show All Robotics
Motor Driver DC 43A H-Bridge PWM Driving BTS7960B
Motor Drivers / PWM Controller, Robotics, Show All RoboticsMotor Driver DC 43A H-Bridge PWM Driving BTS7960B
Double BTS7960 large current (43 A) H bridge driver;
5V isolate with MCU, and effectively protect MCU;
5V power indicator on board;
voltage indication of motor driver output end;
can solder heat sink;
Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2);
SKU: MOD3004 -
Motor Drivers / PWM Controller, Robotics, Show All Robotics
Motor Driver L293D Adafruit Compatible Shield
Motor Drivers / PWM Controller, Robotics, Show All RoboticsMotor Driver L293D Adafruit Compatible Shield
L293D is a monolithic integrated, high voltage, high current, 4-channel driver.Basically this means using this chip you can use DC motors and power supplies of up to 36 Volts, thats some pretty big motors and the chip can supply a maximum current of 600mA per channel, the L293D chip is also what’s known as a type of H-Bridge. The H-Bridge is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor.
SKU: MOD3002 -
Motor Drivers / PWM Controller, Robotics, Show All Robotics
Motor Driver Module L298N MINI 1.5A Dual Channel
Motor Drivers / PWM Controller, Robotics, Show All RoboticsMotor Driver Module L298N MINI 1.5A Dual Channel
motor drive module is ideal for use in battery-powered smart car, toy cars, robots. Supply voltage 2V ~ 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed. Each can provide continuous current of 1.5A, peak current up to 2.5A, thermal protection and can be automatically restored.
SKU: MOD3005