4S 40A 18650 Lithium Battery Protection Board BMS

4S 40A 18650 Lithium Battery Protection Board BMS

Rs.1,295.00
Product Code: ML-2118
Availability: 2-3 Days
Viewed 2757 times

Product Description

Introduction 

Product Name: 3 string 12.6V 40A lithium battery protection board 

Charging voltage: DC 12.6V~13.6V

Continuous discharge current: 40A maximum (if the heat dissipation environment is not good, please reduce the load current)

Continuous charging current: up to 20A

Balance Version Product size: 41*61*4mm

Enhance Version Product size: 41*55*4mm

Applicable choice: applicable to the nominal voltage of 3.7V, fully charged 4.2V lithium battery(including 18650, 26650, polymer lithium battery), can be drilled below 170W

 

Note 1: Successfully start the drill requires 3 10C-20C power batteries, or 6 5C-10C power batteries (recommended power battery models: sony vtc4, vtc4A, vtc5A, vtc6) OV and 12.6V cable, use Copper wire of 3 square millimeters or more (nickel sheets cannot be used)

Note 2: Strictly connect 0V, 4.2V, 8.4V, 12.6V according to the diagram. Do not touch any components on the board when soldering the wire. Do not intentionally short circuit.

Note 3: When soldering the battery for the first time or when charging is in progress, as long as the single battery exceeds 4.2V, the "430" resistor will heat up and discharge (discharge to about 4.19V to stop heating). If the "430" resistor is severely hot, check if the wrong line is connected.

Hardware preparation

Prepare 3S 12.6V 40A lithium battery protection module, battery, power supply, high power load resistor.

The figure below shows the module discharge diagram. The battery is 3 strings. The connected battery needs to meet the 40A discharge current. It can be realized by paralleling the battery or purchasing a battery with a large discharge current. For example, if the battery is 2000mAH and the discharge multiple is 10C, then only 3 strings of 2 are needed and the discharge current is 40A.


Introduction 

Product Name: 4 string 14.8V 16.8V 40A lithium battery protection board

Charging voltage: DC 16.8V~17V

Continuous discharge current: 40A maximum (if the heat dissipation environment is not good, please reduce the load current)

Continuous charging current: up to 20A

Balance Version Product size: 45*60*4mm

Enhance Version Product size: 44*55*4mm

Applicable choice: applicable to the nominal voltage of 3.7V, fully charged 4.2V lithium battery

           (including 18650, 26650, polymer lithium battery), can be drilled below 170W

Note 1: The successful start of the drill requires three 15C-20C power battery, or six 10C-15C power batteries (ordinary 18650 can not start the drill!!).

Note 2: strictly according to map wiring 0V, 4.2V, 8.4V, 12.6V, 16.8V, do not deliberately short circuit.

Note 3: When the load of the brush motor is used, try to connect a non-polar capacitor (withstand voltage above 25V, capacity 10uF-100uF) to the motor's positive and negative terminals to prevent the reverse spike from the motor. Break the MOS tube.

Note 4: 4 groups of batteries in series, please ensure that the voltage of each group of batteries, if not the same, please fill each battery separately and then use in series. In the Discharge test, the voltage drops faster battery the group is poor battery.

The battery is 4 strings. The connected battery needs to meet the 40A discharge current. It can be realized by paralleling the battery or purchasing a battery with a large discharge current. For example, the battery 2000mAH, the discharge multiple 10C, then only need 4 series 2 and the maximum current can reach the discharge current 40A, stable discharge requires 4 strings 4 and can be, and need to pay attention to heat dissipation, the discharge battery power will drop rapidly.


Introduction 

Product name:3S lithium battery protection board 60A enhanced version

(1) Product description:This product is used to charge / discharge three groups of lithium batteries in series, and each group can connect multiple lithium batteries in parallel. It can

Withstand continuous charging current 20A, continuous discharge current 40A, instantaneous current below 80A. used

During the process, the heat dissipation conditions should be good. If the heat dissipation conditions are not good, please reduce the current usage and do not let the board

The child has a noticeably hot feeling. During charging and discharging, it has overcharge protection, overdischarge protection, and overcurrent

Protection, short circuit protection. This product can be used in electric drills, sprayers, LED lights, low power reverse.

Charge and discharge batteries of transformers and other products.

(2) Product parameters:

◆ Product model: HW-552;

◆ Size: 41 * 60 * 1mm;

Charging voltage: 12.6V-13V;

◆ Maximum working current: 60A (heat dissipation conditions are very good);

◆ Continuous charging current (upper limit): 20A;

◆ Continuous discharge current (upper limit): 40A;

◆ Overcurrent protection: 125A;.

◆ Overcharge detection: 12.8V (for 3 groups of batteries);

◆ Overcharge release: 12.3V (for 3 groups of batteries);

◆ Over-discharge detection: 2.4V (for 1 group of batteries);

◆ Over-discharge release: 3.0V (for 1 group of batteries);

◆ Short circuit protection: Yes;

◆ Working temperature: -40-- + 85C;

◆ Storage conditions: -40-- + 125C.

(3) Instructions for use:

Three usage scenarios

A. Charging (overcharge protection)

(1) First, the wiring must be strictly in accordance with the above figure. Use good wires and good contact Good, because even a small resistance will cause a large current to flow. Pressure drops and generate a lot of heat, which affects the performance of the board.

(2) Connect the 13V power supply to the charging end of the board and start charging.

(3) The board will detect the total series voltage of the three groups of batteries. When the voltage reaches 12.8V, the board will Turn off the battery charging circuit, this is the overcharge protection

(4) When the battery pack voltage drops below 12.3V, the overcharge protection contacts and the board will open again The battery charging circuit is overcharged.

(5) If the board turns on overcurrent / short circuit protection for some reason during charging, you remove the connection on the load side, and then turn off the power and restart, you can cancel the overcurrent protection.

You can also disconnect the load, wait a few seconds, and the overcurrent protection is automatically canceled.

B. Discharge (over-discharge protection)

Even if the resistance is not too large, when a large current flows, it will cause a large voltage drop, and

Generates a lot of heat, which affects the performance of the board.

(2) Turn on the load, and the lithium battery pack supplies power to the load through the board. With good heat dissipation, the board can

Withstand a continuous current of 40A, if the heat dissipation is very good, even to reach 60A.

(3) During the discharging process, when it is detected that the voltage of a certain group of batteries drops to the over-discharge voltage limit, the board

Turn on over-discharge protection and turn off the discharge. Note that the battery voltage detected during board discharge

It Will be lower than measuring the voltage across the battery with a multimeter, which is caused by the wires and the battery

, So after the over-discharge protection is turned on, you use a voltmeter to measure the voltage across the battery, which is often higher than

2.4V. In addition, the “0v” terminal on the board and the battery indirect line are not good, which will cause over-discharge.

The protection voltage is higher than 2.4V.

(4) When the battery voltage rises above 3V, the over-discharge protection is released. If over-discharge protection is not available

In addition, the load can be disconnected and the over-discharge protection will be released.

C. Overcurrent protection.

When the current is too large, the board turns on overcurrent protection, the line connection is disconnected, and the charging or

Discharge.

Successful start of electric drill conditions:

(1) The discharge current of the battery must reach the minimum starting current of the electric drill;

(2) The connection between the battery pack and the protection board should be as short as possible, and the wire core should be as thick as possible;

(3) Other conditions are found and supplemented separately.

Write a review

Please login or register to review

When you order from duino.lk, you will receive a confirmation email. Once your order is shipped, you will be emailed the tracking information for your order's shipment. You can choose your preferred shipping method on the Order Information page during the checkout process.

The total time it takes to receive your order is shown below:

The total delivery time is calculated from the time your order is placed until the time it is delivered to you. Total delivery time is broken down into processing time and shipping time.

Processing time: The time it takes to prepare your item(s) to ship from our warehouse. This includes preparing your items, performing quality checks, and packing for shipment.

Shipping time: The time for your item(s) to travel from our warehouse to your destination.

Shipping from your local warehouse is significantly faster. Some charges may apply.

In addition, the transit time depends on where you're located and where your package comes from. If you want to know more information, please contact the customer service. We will settle your problem as soon as possible. Enjoy shopping!